PAINTS

IA / PA
LONG LASTING ANTICORROSION SYSTEM
FORMULATED WITH DESMODUR™ RESIN

 

 

---

 ►  Easy to use, fast drying
 ►  No sanding between coats
 ►  This system hardens by reacting with moisture in the air
 ►  Application preferably by brush, also possible by roller or airless spray gun
 ►  Apply one thin coat of IA on bare metal, for absorption by substrate, then overcoat with 5 layers of PA
 ►  IA: 14 m²/l per coat
 ►  PA: 12 m²/l per coat
 ►  Wait 5 h. between coats at 15°C, 6 to 8 h at 10°C (valid for both)
 ►  Thinner: DP
 ►  Packing: 0.35 l
 ►  Colours:
 ►  IP: grey
 ►  PA: red

This anti-corrosion system is made of a pore-plugged impregnation paint (IA) and a protective paint (PA). IA and PA are very easy to use in most weather conditions (temperature above 0°C). This system ensures a long term protection of metallic surfaces against corrosion in marine environment. PA can be overcoated (poor resistance to ultraviolet rays). By spray gun application, it is necessary to add some thinner.

 

 

 

 

 

P7
ADHESION AND ANTICORROSION PRIMER
FOR PROPELLER AND Z-DRIVE

 

 

---

 ►  Adhesion primer for A7 T.Speed antifouling
 ►  1.5 m²/spray
 ►  2 coats are recommended
 ►  Do not apply under 10°C
 ►  At 15°C wait 15 min. between coats
 ►  1 h before launching
 ►  Cleaner: DP
 ►  Packing: spray 0.300 ml
 ►  Colour: metalic gray

P7 spray primer is an adhesion and protective primer for propeller. Easy to apply, P7 can be applied directly on a new propeller or with Acralu + P7 for maintenance.

 

 

 

 

P1
QUICK DRYING UNIVERSAL PRIMER FOR GRP
ADHESION, WOOD PREGNATION AND ANTICORROSION

 

 

---

 ►  1 pot adhesion primer recommended alos as versatile undercoat for all major antifouling schemes and conversion coat for unknow antifouling
 ►  Apply 1 coat to improve the adhesion of paint on GRP surface
 ►  Application methods: brush, roller, spray gun
 ►  8.5 m²/l per coat
 ►  Application advises:
 ►  Adhesion: 1 coat
 ►  Protection: 4-5 coat minimum
 ►  For wood: thin 10-20% the first coat
 ►  At 15°C hand dry in 45 min., overcoating after 1h30
 ►  Thinner: DP
 ►  Packing: 0.75 l
 ►  Colour: metalic grey

Application of P1 Nautix primer: on gelcoat or paint: reinforcement of antifouling adhesion on classical wood: provides a good impregnation and protection

 

 

 

 

Acralu
ETCH PRIMER FOR ALUMINIUM
AND GALVANISED STEEL

 

---

 ►  Thoroughly mix hardener with base
 ►  Mixing ratio is 1/1 in weight
 ►  Application methods: brush, roller or spray gun
 ►  One thin coat only
 ►  15 m²/l in one coat
 ►  At 15°C: overcoating quickly when hand dry with protective primers PA or HPE
 ►  Thinner: DP
 ►  Packing: 0.5 L
 ►  Colour: yellow

Acralu - etch-primer is a two-pack paint made to ensure adhesion on aluminium, galvanized steel, zinc, bronze and lead. Only one coat of Acralu should be applied before overcoating with PE, HPE or PA protection primers, fillers and finishing undercoats.

 

DP
THINNER FOR PRIMERS
AND TWIN-PACK ENAMELS

---

 ►  For primer PO, IA, PA, P1, HPE, PE, Acralu
 ►  For ultra glide paint White T.Speed
 ►  For undercoat U2
 ►  For enamel L2
 ►  For vanish VA2
 ►  For Nautix grip: two pack non skid
 ►  Packing: 0.75 L

DP thinner into a twin-pack product must be done after the mix of the 2 components.

 

DA
THINNER FOR ANTIFOULING
AND DECK GRIP

---

 ►  For antifouling
 ►  For deck grip: one spot non skid
 ►  For hull cleaning after AS stripper application
 ►  Effective cleaner for spots of tar
 ►  Packing: 0.75 L

DA thinner for antifoulings and Deck Grip. Also very efficient for removing tar stains.

 

A88
PREMIUM ANTIFOULING FOR SUPER YACHT, HEAVY
FOULING AREAS AND HOT WATER CONDITIONS

 

---

 ►  Slow ablative high strength antifouling with systemic and selective preventive actions
 ►  Suitable for all types of boats except aluminium hulls
 ►  8.5 m²/L per coat, 2 to 3 coats are recommended
 ►  At 15°C: wait 3 h between coats
 ►  3 h before launching
 ►  Thinner: DA
 ►  Recommended primers:
 ►  Adhesion: P1, PO или PE
 ►  Protection: PO, PE или HPE (2 coats)
 ►  Osmosis prevention: PO или HPE (5 coats)
 ►  Anticorrosion: PA (3 coats minimum)
 ►  Packing: 2.5 L
 ►  Colour: navy blue

A88 is a very high strength formula adapted for hot water coastal or trans-ocean sailings over any type of vessel. CLR technology (controlled leaching rate) induces a long term selective, systemic, and preventive action over the largest scope of fouling. The high solid volume of Nautix A88 limits the solvent evaporation. The association of specific biocides and a controlled leaching rate of the resin results a long term action over fouling.

 

A7 T.speed
HARD MATRIX
ANTIFOULING

 

---

 ►  2 m²/spray, 5 to 6 coats are recommended
 ►  At 15°C - wait ¼ h between coats
 ►  3 h before launching
 ►  Packing: 0.5 L
 ►  Colour: grey

A7 T.Speed antifouling can be applied on protected aluminium engine drive legs and propellers. The hardy spray allows easy application (painting areas of the give leg which, are difficult to reach with a brush). You can apply A7 T.Speed directly on top of the original coating of the engine provided that surface has been degreased and sanded. On bare aluminium applay first one coat of Acralu  before PA or P7 primer and then antifouling.

A7 T.speed
HARD MATRIX
ANTIFOULING

 

---

 ►  2 m²/spray, 5 to 6 coats are recommended
 ►  At 15°C - wait ¼ h between coats
 ►  3 h before launching
 ►  Packing: 0.5 L
 ►  Colour: black

A7 T.Speed antifouling can be applied on protected aluminium engine drive legs and propellers. The hardy spray allows easy application (painting areas of the give leg which, are difficult to reach with a brush). You can apply A7 T.Speed directly on top of the original coating of the engine provided that surface has been degreased and sanded. On bare aluminium applay first one coat of Acralu  before PA or P7 primer and then antifouling.

A7 T.speed
HARD MATRIX
ANTIFOULING

 

---

 ►  12.5 m²/L per coat, 3 to 4 coats are recommended
 ►  At 15°C - wait 3 h between coats
 ►  3 h before launching
 ►  Thinner: DA
 ►  Packing: 2.5 L
 ►  Colour: grey

A7 T.Speed antifouling can be applied on protected aluminium engine drive legs and propellers. The hardy spray allows easy application (painting areas of the give leg which, are difficult to reach with a brush). You can apply A7 T.Speed directly on top of the original coating of the engine provided that surface has been degreased and sanded. On bare aluminium applay first one coat of Acralu  before PA or P7 primer and then antifouling.